Engine mechanical (2JZ-GTE)
SST (Special service tools)
|
09201-10000 | Valve Guide Bushing Remover & Replacer Set | |
|
09201-01060 | Valve Guide Bushing Remover & Replacer 6 | |
|
09202-70020 | Valve Spring Compressor | |
|
(09202-00010) | Attachment | |
|
09213-70010 | Crankshaft Pulley Holding Tool | |
|
09222-30010 | Connecting Rod Bushing Remover & Replacer | |
|
09223-15030 | Oil Seal & Bearing Replacer | Crankshaft rear oil seal |
|
09248-55040 | Valve Clearance Adjust Tool Set | |
|
(09248-05410) | Valve Lifter Press | |
|
(09248-05420) | Valve Lifter Stopper | |
|
09301-00110 | Clutch Guide Tool | 2JZ-GE M/T |
|
09316-60011 | Transmission & Transfer Bearing Replacer | |
|
(09316-00011) | Replacer Pipe |
Crankshaft front oil seal
Camshaft oil seal |
|
(09316-00051) | Replacer “D” | Camshaft oil seal |
|
09330-00021 | Companion Flange Holding Tool | Crankshaft pulley |
|
09816-30010 | Oil Pressure Switch Socket |
Knock sensor
Oil pressure switch |
|
09843-18020 | Diagnosis Check Wire | |
|
09950-50010 | Puller C Set | |
|
(09951-05010) | Hanger 150 |
Crankshaft pulley
Crankshaft timing pulley |
|
(09952-05010) | Slide Arm |
Crankshaft pulley
Crankshaft timing pulley |
|
(09953-05010) | Center Bolt 100 |
Crankshaft pulley
Crankshaft timing pulley |
|
(09953-05020) | Center Bolt 150 |
Crankshaft pulley
Crankshaft timing pulley |
|
(09954-05010) | Claw No.1 | Crankshaft timing pulley |
|
(09954-05030) | Claw No.3 | Camshaft pulley |
|
09950-70010 | Handle Set | |
|
(09951-07100) | Handle 100 |
Crankshaft rear oil seal
Valve guide bushing |
|
09960-10010 | Variable Pin Wrench Set | |
|
(09962-01000) | Variable Pin Wrench Arm Assy | Camshaft timing pulley |
|
(09963-01000) | Pin 10 | Camshaft timing pulley |
Recommended tools
|
09040-00010 | Hexagon Wrench Set | |
|
09043-50100 | Bi–hexagon Wrench 10 mm | Cylinder head bolt |
|
09044-00020 | Torx Socket E10 | A/C compressor stud bolt |
|
09090-04020 | Engine Sling Device | For suspending engine |
|
09200-00010 | Engine Adjust Kit | |
|
09258-00030 | Hose Plug Set |
Equipment
| OBDII scan tool | Engine speed |
| Caliper gauge | |
| CO/HC meter | |
| Compression gauge | |
| Connecting rod aligner | |
| Cylinder gauge | |
| Dial indicator | |
| Dye penetrant | |
| Engine tune-up tester | |
| Heater | |
| Micrometer | |
| Mirror | |
| Magnetic finger | |
| Piston ring compressor | |
| Piston ring expander | |
| Plastigage | |
| Precision straight edge | |
| Spring tester | Valve spring |
| Steel square | Valve spring |
| Thermometer | |
| Torque wrench | |
| Valve seat cutter | |
| Vernier calipers | |
| V-block |
SSM (Special Service Materials)
| 08826-00080 |
Seal Packing Black or equivalent
(FIPG) |
No.1 camshaft bearing cap
Cylinder head Rear oil seal retainer |
| 08833-00070 |
Adhesive 1324,
THREE BOND 1324 or equivalent |
Drive plate bolt (A/T)
Union for oil cooler hose (2JZ-GTE) |
| 08833-00080 |
Adhesive 1344
THREE BOND 1344 LOCTITE 242 or equivalent |
Idler pulley pivot bolt
Oil pressure switch |
This guide is based on the book edition Toyota (RM502U, 1997)
Volksbibliothek, info@volksbibliothek.com
Back Next